Plumbing Essentials: An Essential for When Installing a Bathtub
Plumbing Essentials: An Essential for When Installing a Bathtub
Blog Article
Almost everyone is bound to have their own perception in relation to How to Install a Bathtub Yourself.
Installing a bathtub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, and also occasionally, tiling abilities. Replacing an old bath tub with a new one is also a reasonably tough project. If the old bathtub is readily accessible, the job can move easily; if you have to open up a wall to eliminate the old bathtub as well as position the new bath tub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will certainly need a helper to move out the old tub as well as embeded in the brand-new one. Make certain you have qualified on your own for the job and are comfortable attempting it. Instead of working with a specialist to take control of a halfway-completed task, it is much better to take into consideration employing one prior to you begin. Opportunities are you might require an expert plumber to make tube links.
This write-up will certainly assist you set up a new bathtub in your restroom if you have currently acquired a brand-new tub and do not require to alter the arrangement of your previous water supply pipelines.
Your tools and product checklist should consist of the following:
Preparing for the Installment
Firstly, the sustaining frame supplied with the bathroom should be fitted (if needed) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the taps unit to avoid strain on the bath tub.
Fit the flexible faucet connectors to the bottom of the two faucets making use of 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its final position.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, after that the first thing you must do is separate the water. After doing so, turn on the faucets to drain any kind of water continuing to be in the system. The process of removing the existing taps can be quite problematic as a result of the restricted gain access to that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a towel ready for the remaining water that will come from the pipelines. As soon as the supply pipes have actually been removed, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Before carrying on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Installing the Tub
Utilizing the two wood boards under its feet, place the tub in the needed position. The wood boards are practical in evenly spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto 4 little factors.
The next goal is to make certain that the bathtub is leveled all round. This can be achieved by checking the level as well as adjusting the feet on the bathtub till the level reviews level.
To mount taps, fit the bottom of the furthest adaptable faucet connector to the appropriate supply pipe by making a compression sign up with; then do the very same for the other tap.
Activate the water and also examine all joints and brand-new pipework for leaks and also tighten them if needed. Fill the bath tub as well as additionally examine the overflow electrical outlet and the regular outlet for leaks.
Finally, take care of the bath paneling as described in the producer's instruction manual. Tiling as well as sealing around the bathtub needs to wait till the bathtub has been used at the very least when as this will resolve it into its final setting.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, then you will require lowering couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin making sure that the washers are in place in between the tap as well as the sink. Secure the faucet in place with the maker given backnut. As soon as the tap is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet ports. The former type should be attached to the tap ends first, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bathroom fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to split a rigid seal, causing the water to permeate the wall surface in between the bathroom and also the tiling, leading to difficulties with dampness as well as possible leaks to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, as well as can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of soaked newspaper or soft rope. Remember to constantly fill up the tub with water before securing, to enable the activity experienced when the bathtub is in use. The sealer can break relatively early if you do not take into account this activity prior to sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise quickly available on the market. It is advisable to fit the ceramic tiles making use of waterproof or waterproof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our topic on A Step-by-Step Guide to Installing a Bathtub. Thanks for taking a few minutes to read through our content. Are you aware of somebody else who is excited by the niche? Please feel free to share it. I enjoy reading our article about A Step-by-Step Guide to Installing a Bathtub.
Address plumbing needs. Report this page