Your Plumbing Crash Course: A Guide to Bathtub Installation
Your Plumbing Crash Course: A Guide to Bathtub Installation
Blog Article
We have come across this article about How to Install a Bathtub directly below on the internet and decided it made sense to share it with you in this article.
Mounting a bath tub isn't exactly rocket science, however it does require solid plumbing, woodworking, and occasionally, tiling abilities. Changing an old bath tub with a new one is additionally a reasonably hard project. If the old tub is readily available, the job can move easily; if you need to open a wall to eliminate the old bathtub and position the brand-new bathtub, the task is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub and set in the new one. See to it you have actually certified on your own for the task as well as are comfortable trying it. As opposed to hiring a service provider to take over a halfway-completed task, it is far better to consider employing one before you start. Possibilities are you may require a specialist plumber to make tube connections.
This write-up will certainly assist you mount a brand-new bath tub in your shower room if you have actually already gotten a new tub and also don't need to change the setup of your previous water pipes.
Your devices and also product checklist need to comprise the following:
Preparing for the Setup
To start with, the sustaining framework supplied with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets system to avoid pressure on the bathtub.
Fit the adaptable tap ports to the bottom of the two faucets making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you utilize every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be suited its last position.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, after that the first thing you should do is separate the water system. After doing so, turn on the faucets to drain any water continuing to be in the system. The procedure of getting rid of the existing taps can be rather problematic due to the restricted access that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipes have been eliminated, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from transforming during this process. When the faucets have been eliminated, the holes in the bath/basin will need to be cleaned up of any kind of old securing substance.
Before moving on to fit the brand-new taps, contrast the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Using the two wooden boards under its feet, place the bath tub in the required placement. The wooden boards are valuable in equally spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto 4 small points.
The following objective is to guarantee that the bathtub is leveled all round. This can be achieved by inspecting the level and readjusting the feet on the bath tub till the spirit level checks out degree.
To install taps, fit all-time low of the furthest versatile tap port to the suitable supply pipeline by making a compression join; then do the very same for the various other tap.
Activate the water system as well as check all joints and also new pipework for leakages and tighten them if necessary. Fill the tub as well as additionally examine the overflow outlet and the regular electrical outlet for leaks.
Lastly, take care of the bath paneling as explained in the supplier's user's manual. Tiling as well as securing around the bathtub should wait up until the bathtub has been used at least when as this will resolve it right into its final placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washing machines remain in area in between the faucet as well as the sink. Secure the tap in place with the manufacturer supplied backnut. As soon as the faucet is firmly in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The previous type needs to be attached to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bath fulfills the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to break a stiff seal, triggering the water to penetrate the wall surface between the bath as well as the tiling, causing complications with wetness as well as possible leakages to the ceiling listed below.
You can pick from a range of coloured sealers to assimilate your components and fittings. They are marketed in tubes and cartridges, as well as are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly load the bath tub with water prior to securing, to allow for the movement experienced when the tub remains in use. The sealant can break rather early if you do not take into account this movement prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise conveniently available on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or water resistant adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
We hope you enjoyed our section on Tools You Need to Install a New Bathtub . Many thanks for finding the time to browse our article post. Loved our entry? Please share it. Let somebody else check it out. Thank you for going through it.
Stress-free? Call now! Report this page